null
​Set of Three Celestial Stretch Bracelets

​Set of Three Celestial Stretch Bracelets

Set of Three Celestial Stretch Bracelets

Materials Needed:

4mm Round Mother of Pearl (74)

6mm Round Mother of Pearl (26)

6mm Silver Stardust Beads (3 for covering knots)

2mm Round Sterling Silver Beads (6)

.7mm Stretch Magic (1)

8-10mm Mother of Pearl - Donut (4)

10mm White Seashell - Flat Star (3)

12mm White Seashell - Triangle (2)

Hypo Cement Glue



Tools Required:

Scissors

Bead Stopper

Bead Mat

Finished Interior Fit 7” (You can add or detract beads to accommodate your wrist size)


Instructions on Construction:


First Bracelet – “3 Celestial Stars Bracelet”

1. Cut 1 x 12” pieces of Stretch Magic, pre-stretch cord then attach bead stop to one end of stretch cord about 2 1/2” from end

2. Add 18 x 4mm mother of pearl, 1 x star, 1 x 2mm sterling silver bead, 1 x star, 1 x silver bead, 1 x star, 18 x 4mm mother of pearl and 1x 6mm silver stardust bead.

3. Tie three square knots and tighten firmly between each knot.

4. Thread one of the tails back through the silver stardust bead, add a dab of hypo cement onto the knot (from all sides). Pull tail to center knot in the middle of the stardust bead, you should have one tail sticking out either side of the bead.

5. Leave the bracelet for at least a couple of hours for the hypo cement to set up, then trim tails. You can hold onto one tail, pull the opposite tail & trim close as you can. The other side you just trim as close as you can as you have nothing to hold onto :)


Second Bracelet – “3 Celestial Rings Bracelet ”

1. Cut 1 x 12” pieces of Stretch Magic, pre-stretch cord then attach bead stop to one end of stretch cord about 2 1/2” from end.

2. Add 19 x 4mm mother of pearl, 3 x donuts with a silver bead inside of each donut (it is a little tricky to get the silver bead on to the cord, if you leave them both flat on the bead mat and look down from above you can tell when the opening in the silver bead lines up) 19 x 4mm mother of pearl & 1 x 6mm stardust bead.

3. Tie three square knots and tighten firmly between each knot.

4. Thread one of the tails back through the silver stardust bead, add a dab of hypo cement onto the knot (from all sides). Pull tail to center knot in the middle of the stardust bead, you should have one tail sticking out either side of the bead.

5. Leave the bracelet for at least a couple of hours for the hypo cement to set up, then trim tails. You can hold onto one tail, pull the opposite tail & trim close as you can. The other side you just trim as close as you can as you have nothing to hold onto :)


Third Bracelet – “Celestial Triangle Bracelet”

1. Cut 1 x 12” pieces of Stretch Magic, pre-stretch cord then attach bead stop to one end of stretch cord about 2 1/2” from end.

2. Add 13 x 6mm mother of pearl, 1 x 12mm triangle, 1 x donut with 2mm sterling silver bead set inside, 1 x 12mm triangle, 13 x 6mm mother of pearl and 1x 6mm silver stardust bead.

3. Tie three square knots and tighten firmly between each knot.

4. Thread one of the tails back through the silver stardust bead, add a dab of hypo cement onto the knot (from all sides). Pull tail to center knot in the middle of the stardust bead, you should have one tail sticking out either side of the bead.

5. Leave the bracelet for at least a couple of hours for the hypo cement to set up, then trim tails. You can hold onto one tail, pull the opposite tail & trim close as you can. The other side you just trim as close as you can as you have nothing to hold onto :)

6. Try on your new bracelets & admire your handiwork

7. Enjoy!

Jewelry designed by Steph Stirniman at magpiecollectives.com

18th May 2020 Steph Stirniman

Recent Posts